Important Plumbing Guide for Bathtub Installation
Important Plumbing Guide for Bathtub Installation
Blog Article
What're your opinions about How to Install a Bathtub?
Installing a bath tub isn't specifically brain surgery, yet it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bathtub with a new one is also a moderately hard job. If the old tub is conveniently easily accessible, the task can relocate easily; if you need to open up a wall surface to remove the old bathtub and position the new tub, the task is a lot harder. In either case, the project is within a home handyman's skills, although you will need a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have qualified yourself for the task and also fit trying it. As opposed to working with a specialist to take control of a halfway-completed task, it is much better to consider utilizing one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This short article will aid you set up a new tub in your shower room if you have actually already gotten a new bathtub and don't need to change the setup of your previous water pipelines.
Your devices and product list ought to consist of the following:
Preparing for the Installment
Firstly, the sustaining frame provided with the bathroom should be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the faucet features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps system to stop pressure on the bath tub.
Fit the adaptable tap adapters to the bottom of the two taps using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its last placement.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you ought to do is separate the water supply. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the limited access that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel all set for the continuing to be water that will come from the pipelines. As soon as the supply pipes have actually been removed, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Making use of both wood boards under its feet, put the tub in the called for setting. The wooden boards are valuable in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the tub till the spirit level checks out level.
To set up faucets, fit the bottom of the outermost adaptable faucet connector to the proper supply pipe by making a compression join; then do the exact same for the other faucet.
Switch on the water system and also examine all joints and new pipework for leaks as well as tighten them if essential. Load the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub should wait till the tub has been used at the very least when as this will settle it right into its final position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washers remain in area between the faucet and the sink. Safeguard the tap in place with the supplier provided backnut. When the faucet is securely in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture an inflexible seal, creating the water to permeate the wall between the bathroom and also the tiling, causing issues with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill the tub with water before sealing, to allow for the motion experienced when the bathtub is in usage. The sealant can split fairly early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently offered on the market. It is advisable to fit the tiles making use of water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Do you really like reading about Installing A Bathtub? Write feedback down below. We'd be glad to hear your reactions about this blog posting. We hope that you come back again in the near future. Liked our post? Please share it. Let someone else find it. Thanks for taking the time to read it.
Quote & Schedule Report this page